Application of additive in the slurry of sanitary ware;
衛生陶瓷泥漿添加劑的應用研究
The super-smooth glaze of sanitary ware was obtained by once-fired technique.
采用一次燒成工藝制備了衛生陶瓷用超平滑釉(Ra≤10。
The present developing status and standards of sanitary ware industry are summarized in this paper.
歸納了當今衛生陶瓷工業的發展現狀和水平 ,對窯爐產業提出了的新要求 ,分析了某一新型窯爐的特點 ,對發展我國陶瓷窯爐產業提出了建
Complexity of the gelcasting process for sanitary ceramics makes it difficult to control the dry shrinkage of the green body.
衛生陶瓷凝膠注模成型工藝的復雜性使其很難控制材料成型后的干燥收縮率,嘗試用人工神經網絡技術對衛生陶瓷凝膠注模成型工藝過程進行識別和仿真,采用Levenberg-Marquardt算法建立了衛生陶瓷凝膠注模成型工藝中單體、引發劑、交聯劑、催化劑含量和坯體干燥收縮的映射網絡模型,從而可利用該模型來預測在一定有機成型添加劑含量下衛生陶瓷的干燥收縮。
Temperature and humidity in casting workshop for sanitary ceramics are very important for the quality of semi-finished product, but the traditional drying system is mostly independent.
衛生陶瓷成型車間的溫度和濕度對半成品的成品率至關重要,其熱源大都采用單獨供應的辦法,本文介紹了利用隧道窯余熱對成型車間供熱的情況。
In order to controll the gelcasting process of sanitary ceramics by computer, a prediction model for the properties of shaped green sanitary ceramics body prepared by gelcasting based on BP artificial neural net is established.
為了實現對衛生陶瓷凝膠注模成型工藝的計算機控制,采用BP神經網絡對獲得的實驗數據進行訓練,建立了衛生陶瓷凝膠注模成型工藝參數和成型后坯體性能的映射網絡模型,從而可利用該模型來預測在一定工藝條件下衛生陶瓷的性能。
The applications of Guangxi-Qidao clay in ceramic paste and glaze of sanitary wares are studied on the basis of the study about the clay’s raw material capability.
在對廣西氣刀土原料性能研究的基礎上,進行了在衛生陶瓷坯料、釉料中的應用研究。
Through the adjust ion of Si/Al proportion and the doping of talc and matting agents,a calcium mat glaze for sanitary wares has been developed in this experiment.
本試驗通過調整衛生陶瓷釉漿中的Si/Al,引入滑石和無光劑 ,成功地制備出衛生陶瓷鈣質無光釉。
The slip properties of the pressure casting on sanitary wares are studied,through a series of test,the influence of the slip properties of the slip casting process are discussed.
研究了衛生陶瓷壓力注漿成型的泥漿性能 ,通過一系列試驗 ,討論了泥漿性能對壓力注漿成型的影響。
The effect of industrial wastes on the properties of ceramic slurry for sanitary ceramics was studied,and the optimum introduced quantity of the wastes was difined.
研究了一些工業廢物對衛生陶瓷泥漿性能的影響 ,并確定了這些廢物的最佳引入量。
This paper describes what quality data should be collected from each procedure of sanitary ceramic manufacture,analyzes the importance of these data,and introduces application of these data through QC tools to improve and evaluate the procedure of products development in ceramic field.
闡述了衛生陶瓷各工藝過程需要采集的主要質量數據,分析說明了這些數據的重要性,同時介紹了如何應用QC工具加以分析利用這些數據,用以改善和評估衛生陶瓷新產品的研發試驗過程。
This article elaborated the production technology、quality control and measurement methods of gypsum powder used in sanitary ceramic working mold.
闡述了我國衛生陶瓷工作模用石膏粉的生產工藝、質量控制、檢測方法等的現狀;對我國具有代表性的石膏粉產品取樣并進行了性能撿測、分析;研究了影響石膏粉質量和石膏模質量的主要因素:提出了建立衛生陶瓷工作模用石膏粉產品標準和檢測標準的必要性。
The cross experimental research of Gel-casting technology on sanitary by using hydroxymethylacrylamide(HMAM)as monomerand ceric ammonium nitrate as initiator,N,N,N',N'-tetramethylethylenedimaine as catalyst,N,N'-methylenebisacrylamide(MBAM)as cross-linkeris conducted.
本文采用正交實驗方法,以羥甲基丙烯酰胺為單體,硝酸鈰銨為引發劑,N,N,N',N'-四甲基乙二胺為催化劑,N,N'-亞甲基雙丙烯酰胺為交聯劑,研究了衛生陶瓷凝膠注模成型工藝,并探討了不同工藝條件(單體加入量、引發劑加入量、催化劑加入量、交聯劑加入量等因素)對衛生陶瓷料漿凝膠注模成形后坯體的干燥速率、收縮率、干燥強度以及綜合性能指標的影響規律。
Gelcasting technology of sanitary using acrylamide as monomer and (NH 4) 2S 2O 8-NaHSO 3 as redox initiator was studied.
采用凝膠注模成型方法 ,以丙烯酰胺為單體 ,( NH4 ) 2 S2 O8-Na HSO3為引發劑 ,研究了衛生陶瓷凝膠注模成型工藝。
Based on a SWOT analysis the author summarized the strategic choices available for theGuangdong construction ceramics enterprise in its cerrent state.
通過對佛山、東莞等地的陶瓷產區相關企業的調查研究,在SWOT分析的基礎上,研究了相關的競爭戰略,歸納總結出現階段適合建筑衛生陶瓷企業的戰略:即以低成本為競爭生存方式,差異性為競爭發展動力,國際化為發展長期最終目標。
Due to the large amount of research required for this article, what's presented here is a summary of the current situation of construction ceramics in certain geographical locations, paying particular attention to the province of Guangdong.
文章通過大量的調查研究,概述了中國特別是廣東省建筑衛生陶瓷企業的現狀,采用SWOT分析方法,對該行業的企業所處的優勢、劣勢、面對的機遇和挑戰進行了全面的研究分析,預測了建筑衛生陶瓷未來發展的總體趨勢。
The Life Cycle Assessment of Sanitary Ware in China
我國衛生陶瓷生命周期影響評價研究
Test methods for water absorption for architectural and sanitary ceramics
GB/T2579-1989建筑衛生陶瓷吸水率試驗方法
DISCUSSABOUT COMPETING ENVIRONMENT OF CHINESE CONSTRUCTION SANITARY CERAMIC ENTERPRISE;
中國建筑衛生陶瓷企業競爭環境淺析
Life Cycle Assessment of the Typical Sanitary Ware Company of China
我國衛生陶瓷典型企業生命周期評價研究
An Analysis on Prsent Quality Situation of Sanitary Wares in Guangdong Province;
近期廣東省衛生陶瓷產品質量狀況及分析
New Tend of Competition on the Constructing Sanitation Ceramics Product Market ,Culture Business;
建筑衛生陶瓷產品市場競爭新趨勢—文化營銷
A VAST PROSPECT FOR THE EXPORT OF CHINESE MEDIUM AND HIGH - GRADE SANITARY PORCELAIN;
我國擴大出口中高檔衛生陶瓷前景廣闊
Superheated Steam Drying Control System Design Based on PLC
基于PLC的衛生陶瓷過熱蒸汽干燥控制系統設計
A Method of 3D Solid Modeling and Development of CAD System for Sanitary Ceramic Products;
衛生陶瓷產品三維實體建模方法與CAD系統的研制
The Research on How the Ceramic Industry to Meet the New Energy-consuming Standard--The Avenue Exploring under the Instruction of Recycling Economy;
新標準下建筑衛生陶瓷行業應對能耗問題的研究——循環經濟思想指導下的途徑探索
ceramic sanitary fixture for connection to water or sewage systems
陶瓷衛生器具,用于連接供水排水系統
ceramic sanitary fixture of porcelain or china indoor for connection to water or sewage systems
室內陶瓷衛生器具,瓷制,用于連接供水排水系統
Live in the water--With water for clues to the thoughts of ceramic sanitary products design
水中生息——以水為線索的陶瓷衛浴產品設計思考
fixture for indoor plumbing, ceramic of porcelain or china for connection to water or sewage systems
陶瓷室內衛生設備,瓷或白坯資制,用于連接供水排水系統
fixture for indoor plumbing, ceramic (excl. of porcelain or china) for connection to water or sewage systems
陶制室內衛生設備（瓷或白坯瓷制的除外）,用于連接供水排水系統
Yatao Ceramics Co., Ltd. is a ceramic sanitary ware manufacturer, which has producing experience for many years.
潮州市亞陶瓷業有限公司是一家具有多年生產經驗的衛浴陶瓷生產商。
From the born day, HONGYU sanitary wares have been devoting to the perfect quality, modeling the life by creative and artistic points of view.
弘宇陶瓷從它誕生的那一天起，就致力捍衛極致的衛浴品質，以創新及藝術的角度塑造生命。
Bolo Bathing Necessities Ceramics Co., Ltd.
上海寶路衛浴陶瓷有限公司